FIXTURE LEVEL
Faucet Repair & Installation in Dallas, GA
A faucet that drips at a steady rate usually needs a new cartridge or washer, not a whole new fixture.
A dripping faucet is almost always a worn cartridge, washer, or O-ring rather than a failure of the fixture itself, and in most cases it's a same-visit repair once the exact fixture and mechanism are identified. Kitchen and bathroom faucets use different internal mechanisms depending on brand and age, which is why a repair sometimes takes longer on an older or discontinued fixture than a newer one.
For a full replacement, whether it's a kitchen faucet, a bathroom faucet, or an outdoor hose bib, we handle the supply line connections and shutoff valves correctly the first time, which matters more here than in a lot of places because a badly seated connection under a slab-on-grade kitchen sink is exactly the kind of slow leak that goes unnoticed for months.
Mineral buildup from a blended water supply
Dallas draws its water primarily from the Richland Creek Reservoir, treated at the Richland Creek Water Treatment Plant, and supplements that supply with water purchased from the Cobb County-Marietta Water Authority. That blended surface-water source carries a moderate mineral content that shows up over time as scale buildup inside faucet aerators and cartridges, which is the most common reason an older faucet starts to feel stiff to turn or sprays unevenly even though nothing has actually broken.
On the county's rural well systems, out toward Braswell and the less developed parts of Paulding County, the mineral profile is different again, often carrying more iron, and that shows up as staining around the faucet spout rather than the smoother white scale typical of the city-supplied side of the county.
Common faucet symptoms and the likely fix
| Symptom | Likely cause | Typical fix |
|---|---|---|
| Steady drip from the spout | Worn cartridge or washer | Cartridge replacement |
| Handle feels loose or wobbly | Worn mounting hardware | Tighten or replace mounting |
| Reduced or uneven spray | Mineral buildup in the aerator | Clean or replace aerator |
| Leak at the base of the faucet | Worn O-ring at the base gasket | O-ring replacement |
Worth knowing
Getting the shutoff valves right during installation
On a lot of Dallas-area kitchen and bathroom remodels, the original shutoff valves under the sink are decades old and seize the first time someone tries to turn them. Part of doing a faucet installation correctly is testing and, when needed, replacing those shutoffs at the same time, rather than reconnecting a new faucet to old valves that are one turn away from failing on their own.
New construction along Dallas's Highway 61 and Highway 278 retail corridor brings a steady stream of straightforward installs on fixtures that are already up to current code, while remodels in the older homes near the downtown square more often turn up compression-style shutoffs that should be swapped for modern quarter-turn valves while the cabinet is already open. We flag that difference during the estimate rather than after removing the old faucet.
Signs it's time for a new fixture instead of a repair
- The faucet is discontinued and replacement cartridges are no longer made
- Multiple leak points on the same fixture within a short span
- Visible corrosion on the fixture body itself, not just the internal parts
Related
One more thing worth knowing: a fixture that's leaking at the shutoff valve rather than the faucet itself is usually a sign those valves need attention as part of any faucet installation or replacement.
Ready to get faucet repair & installation sorted in Dallas or Hiram?
Call (770) 764-0886Questions
Asked about faucet repair & installation in Dallas
Why does our faucet still drip after we tightened the handle?
Tightening the handle only addresses a loose mount. A drip almost always means the internal cartridge or washer has worn out and needs replacing, which is a different repair than adjusting the handle.
Is it worth repairing an older faucet or just replacing it?
If replacement parts are still available and the fixture body itself is in good shape, repair is usually the more affordable option. Once a fixture is old enough that parts are discontinued, replacement is typically the more practical route.
Does hard water actually damage a faucet over time?
Mineral buildup from Dallas's blended surface-water supply can gradually clog an aerator and stiffen a cartridge, which shortens a faucet's comfortable service life even though it rarely causes the fixture to fail outright.
Can you match a new faucet to our existing sink's hole pattern?
Yes, matching the hole spacing and finish is part of a proper installation, and we check that before ordering or bringing a fixture out to avoid a mismatch on the day of the job.
Need faucet repair & installation in Dallas or Hiram?
Call and describe what's happening. You'll reach a plumber, not a form.